Controlling the Default Targets

One of the most basic things you can control is which targets SCons will build by default--that is, when there are no targets specified on the command line. As mentioned previously, SCons will normally build every target in or below the current directory by default--that is, when you don't explicitly specify one or more targets on the command line. Sometimes, however, you may want to specify explicitly that only certain programs, or programs in certain directories, should be built by default. You do this with the Default function:

       env = Environment()
       hello = env.Program('hello.c')
       env.Program('goodbye.c')
       Default(hello)
    

This SConstruct file knows how to build two programs, hello and goodbye, but only builds the hello program by default:

       % scons -Q
       cc -o hello.o -c hello.c
       cc -o hello hello.o
       % scons -Q
       scons: `hello' is up to date.
       % scons -Q goodbye
       cc -o goodbye.o -c goodbye.c
       cc -o goodbye goodbye.o
    

Note that, even when you use the Default function in your SConstruct file, you can still explicitly specify the current directory (.) on the command line to tell SCons to build everything in (or below) the current directory:

       % scons -Q .
       cc -o goodbye.o -c goodbye.c
       cc -o goodbye goodbye.o
       cc -o hello.o -c hello.c
       cc -o hello hello.o
    

You can also call the Default function more than once, in which case each call adds to the list of targets to be built by default:

       env = Environment()
       prog1 = env.Program('prog1.c')
       Default(prog1)
       prog2 = env.Program('prog2.c')
       prog3 = env.Program('prog3.c')
       Default(prog3)
    

Or you can specify more than one target in a single call to the Default function:

       env = Environment()
       prog1 = env.Program('prog1.c')
       prog2 = env.Program('prog2.c')
       prog3 = env.Program('prog3.c')
       Default(prog1, prog3)
    

Either of these last two examples will build only the prog1 and prog3 programs by default:

       % scons -Q
       cc -o prog1.o -c prog1.c
       cc -o prog1 prog1.o
       cc -o prog3.o -c prog3.c
       cc -o prog3 prog3.o
       % scons -Q .
       cc -o prog2.o -c prog2.c
       cc -o prog2 prog2.o
    

You can list a directory as an argument to Default:

       env = Environment()
       env.Program(['prog1/main.c', 'prog1/foo.c'])
       env.Program(['prog2/main.c', 'prog2/bar.c'])
       Default('prog1')
    

In which case only the target(s) in that directory will be built by default:

       % scons -Q
       cc -o prog1/foo.o -c prog1/foo.c
       cc -o prog1/main.o -c prog1/main.c
       cc -o prog1/main prog1/main.o prog1/foo.o
       % scons -Q
       scons: `prog1' is up to date.
       % scons -Q .
       cc -o prog2/bar.o -c prog2/bar.c
       cc -o prog2/main.o -c prog2/main.c
       cc -o prog2/main prog2/main.o prog2/bar.o
    

Lastly, if for some reason you don't want any targets built by default, you can use the Python None variable:

       env = Environment()
       prog1 = env.Program('prog1.c')
       prog2 = env.Program('prog2.c')
       Default(None)
    

Which would produce build output like:

       % scons -Q
       scons: *** No targets specified and no Default() targets found.  Stop.
       % scons -Q .
       cc -o prog1.o -c prog1.c
       cc -o prog1 prog1.o
       cc -o prog2.o -c prog2.c
       cc -o prog2 prog2.o
    

Getting at the List of Default Targets

SCons supports a DEFAULT_TARGETS variable that lets you get at the current list of default targets. The DEFAULT_TARGETS variable has two important differences from the COMMAND_LINE_TARGETS variable. First, the DEFAULT_TARGETS variable is a list of internal SCons nodes, so you need to convert the list elements to strings if you want to print them or look for a specific target name. Fortunately, you can do this easily by using the Python map function to run the list through str:

         prog1 = Program('prog1.c')
         Default(prog1)
         print "DEFAULT_TARGETS is", map(str, DEFAULT_TARGETS)
      

(Keep in mind that all of the manipulation of the DEFAULT_TARGETS list takes place during the first phase when SCons is reading up the SConscript files, which is obvious if we leave off the -Q flag when we run SCons:)

         % scons
         scons: Reading SConscript files ...
         DEFAULT_TARGETS is ['prog1']
         scons: done reading SConscript files.
         scons: Building targets ...
         cc -o prog1.o -c prog1.c
         cc -o prog1 prog1.o
         scons: done building targets.
      

Second, the contents of the DEFAULT_TARGETS list change in response to calls to the Default: function, as you can see from the following SConstruct file:

         prog1 = Program('prog1.c')
         Default(prog1)
         print "DEFAULT_TARGETS is now", map(str, DEFAULT_TARGETS)
         prog2 = Program('prog2.c')
         Default(prog2)
         print "DEFAULT_TARGETS is now", map(str, DEFAULT_TARGETS)
      

Which yields the output:

         % scons
         scons: Reading SConscript files ...
         DEFAULT_TARGETS is now ['prog1']
         DEFAULT_TARGETS is now ['prog1', 'prog2']
         scons: done reading SConscript files.
         scons: Building targets ...
         cc -o prog1.o -c prog1.c
         cc -o prog1 prog1.o
         cc -o prog2.o -c prog2.c
         cc -o prog2 prog2.o
         scons: done building targets.
      

In practice, this simply means that you need to pay attention to the order in which you call the Default function and refer to the DEFAULT_TARGETS list, to make sure that you don't examine the list before you've added the default targets you expect to find in it.